A tilting TV mount is always preferred over a fixed mount as it allows you to adjust the angle of a flat screen.
This is used especially when light shines on a TV and causes glare or if you sit at an angle from where the screen is not right in front of you.
The following guide will help you learn the proper way of adjusting tilt on a full-motion mount.
Quick Summary
The following information will be discussed in the article:
- How to adjust the tilt on a TV mount?
- Benefits of a TV mount with tilt
- How to find the VESA measurement of TV?
How to Adjust the Tilt on a TV Mount?
It is not hard to install tilting TV mounts. It should be noted that the technique can vary from brand to brand. However, the task is pretty much the same. The following are the steps:
Step 1
For the first step, you have to find out the tension knob. These knobs are present on the bracket of full-motion mounts which are attached to the back of the TV.
However, it should be kept in mind that there could be a knob on both sides of the bracket or only on one side.
This depends on the model and making of the TV bracket.
Step 2
For the second step, loosen up the tension knobs. To do this, turn them counterclockwise.
Make sure to hold the TV with one hand during this step so it does not tilt down too quickly whilst the knob is adjusted.
Step 3
To tilt the TV upwards, very gently push the bottom of your TV upwards. Similarly, to tilt the TV downwards, very gently push the top of your TV downwards.
Step 4
Source: Reddit
Once the TV is tilted to the desired position and is on the preferred angle, tighten up all the knobs. This will adjust the wall plates.
To do this rotate them in a clockwise direction and then let go of the TV.
Benefits of Tilting TV Mount
Source: Reddit
A TV mount with tilt has a wall bracket and two adjustable tilted wall mounts arm. Tilt mounts have a very simple design to provide a sleek look that is pleasing to the eye.
This robust mount can provide motion to an extent.
Why is a tilting mount preferred over a fixed mount?
A mount with tilt is preferred over a fixed mount as it allows you to adjust the angle of a flat-screen TV. This is done according to your viewing needs.
If a TV is installed slightly upwards, you can use the motion mounts to tilt the TV downward so the center of the screen is right at your eye level at the right angle.
Similarly, if it is installed lower, you can tilt it slightly upwards to make the viewing angle comfortable for yourself and the best viewing experience.
Will a TV mount with tilt improve picture quality?
A mount with tilt will definitely improve the picture quality of your TV due to the angle adjustment.
This is especially true for LEDs because they lose contrast and clarity when viewed at an angle.
This will also help you if bright sunlight enters your room. The tilt motion will help you adjust the TV stand to an angle where this bright sunlight is not an issue. This way you can have a clear picture quality with no glasses.
How to Find the VESA Measurement of a TV?
The VESA measurement of a TV is considered highly important and has a lot of significance. It is very important to know the basics of it before you decide to buy a TV mount for yourself.
What is the VESA measurement?
Source: Reddit
To understand the VESA measurement, you must first understand what it is. You can find four screw holes at the back of your TV. The distance measured between these holes is the VESA measurement.
In addition to this, you also do not need any expert technique or guide to measure this.
Why is the VESA measurement used?
VESA is taken as a standard measurement of TVs and is accepted by all the major brands. This is done to make sure that customers face no problems when they buy TVs and set them with wall mounts.
The basic concept behind this measurement is to avoid the purchase of a TV wall mount that does not fit with the TV.
How to find out the correct VESA measurements?
The first step to finding out the correct VESA measurement is to look into the instructions manuals of your TV.
By looking at the instruction manual you can easily find where the holes are located exactly.
Then use a ruler or a measuring tape to find the exact distance between these four holes.
You need to make sure that you properly cover both the horizontal and vertical distance between these holes.
How will this help you buy the ideal bracket for your TV?
You need to be aware of the fact that there is a maximum VESA measurement and a minimum VESA measurement.
If the VESA measurement you get from your TV falls into this range then you can be sure that the TV bracket you buy will fit the TV perfectly.
It is advisable to convert these measurements into mm and note them down once you have measured them. Then when you plan to buy the wall bracket you can match the measurements of the bracket with the VESA measurement of your TV to find the perfect wall bracket.
It should be noted that every wall mount with the same VESA number will fit any TV with the same number.
Tilting Wall Mount Wrapping Things Up
You now are familiar with the proper way of adjusting the tilt on a TV wall mount. In addition to this, you have also learned the additional benefits that a wall mount with tilt gives you.
Furthermore, we have also explained in detail the concept of VESA measurement and how it has to be taken. This will ensure that you buy the right kind of wall mount with no chance of an error.
With that, we conclude our guide on how to adjust the tilt on a TV mount.
Let us know if you have any questions or queries related to this.
Adam F.
A/V and Home Theater Expert that focuses on providing clear as well as concise reviews for anything and everything Audio Visual. From TV's, TV Mounts, Soundbars, and Wiring, my focus is to provide expertise in everything Audio Visual focused.